V-a-gtacho USB Version V 5.0 V-A-G Tacho for NEC MCU 24C32 or 24C64

Fuera de existencia. Historia 12 vendidos. Artículo NºSE77

¡Ordene hoy!: 22.95
Peso:
0.4KG
Paquete:
16cm*17cm*2cm     ( Inch: 6.3*6.69*0.79 )
Devoluciones:
Devoluciones: Vuelva para el reembolso dentro de 30 días, el comprador paga el envío de devolución. Leer detalles »

Descripción del producto

V-A-GTacho USB Version V 5.0 is a V-A-G Kombiinstrument / Immo box eeprom programmer and support Windows 7, Vista, Win XP, Win 98.

V-A-G Tacho USB Version V 5.0

vagtacho usb version

Lastest version 5.0, support VDO with 24C32 or 24C64,our v-a-gtacho usb version 5.0 includes the functions of  v-a-gtacho usb 4.52 , v-a-gtacho usb 4.0, and v-a-gtacho usb 3.5

V-A-G Kombiinstrument / Immo box eeprom programmer!

Windows 7, Vista, Win XP, Win 98 compatible software!

Support for some VDO dashes for VW from year 2009-2011 with NEC mcu and 24C32 or 24C64 eeprom memory. Important: These dashes requires ignition to be switched on with valid key of the car! Software version 5.0 works ONLY with interfaces which has got built-in programmer for Megamos ID48 transponders!

Built-in programmer for Megamos ID48 transponders! Pre-programming of TP2x transponders as dealer's keys with component security data which is read from immobiliser!

NEW key programming feature for V-A-G cars with VDO dashes on CAN bus! (TP2 and UDS protocols)



Note: TP22,23,24,25 transponders are required!



List of supported V-A-G cars:



Volkswagen



Golf 6, Jetta, Polo, EOS with VDO dash 2009 - 2011, note: not all dashes are supported!

Golf 5, Caddy, Touran, Jetta, EOS with VDO dash 2003 - June.2006

Golf 4, Bora with VDO or Motometer/Bosch dash: 1997-2003

Beetle with Marelli dash: 1998 - 2005

Passat, Jetta, with VDO, Marelli or Motometer dash: 1997-2004

Polo with VDO or Motometer dash: 1999-2006 (1999-2002 mileage change only)

Sharan with VDO dash: 2000-2004(mileage change only)

Caddy, Lupo with VDO or Motometer dash 1997 - 2002(mileage change only)

Transporter with VDO dash 1998 - 2000

LT35 ( Temic immo box) 1999-2003 (pin code read only)

Gol ( Kostal immo box) 1999-2003 (pin code read only)



Seat



Altea, Leon, Toledo with VDO 2003 - 6/2006

Leon, Toledo, Cordoba, Ibiza with VDO or Motometer dash 1997-2003

Alhambra with VDO 2000 - 2004(mileage change only)

Inca with VDO or Motometer 1997 -2000(mileage change only)



Skoda



Octavia II with VDO dash 2005 - 6/2006

Octavia, Fabia with VDO dash 1997 - 2004



Audi



A3 VDO dash 2003 - 2005

A3,A4,A6 VDO dash 1997 - 2000

A3,TT,A6 Magnetti Marelli dash 1998 - 2003

A4 Bosch dash 2000 - 2008 - Read/write of encrypted data with V4.5!

A4,A6,A8 1995-1999 (immo box - read pin code)



V-a-gtacho usb version 4.52



V-a-gtcho 4.52 is upgraded from v-a-gtacho usb4.0, Upgrade V-a-gtacho usb 4.0 interface with Programmer for Megamos ID48 chips, our v-a-gtacho version 5.0 has upgraded directly ,includes the functions for v-a-gtacho usb 4.52

The benefits with this upgrade are:

Your V-a-gtacho interface will works with software vesrion 5.0 for the new VDO dashes with UDS protocol from year 2009+

Programming of new keys to V-A-G cars which are into FAZIT database.

Works with cars which has got locked key programming channel, or pin code is not accepted.

No need to wait up to 30 minutes for the key programming procedure.

With this upgrade, V-a-gtacho can program the new key in one minute



V-a-gtacho version 4.0



V-A-G Kombiinstrument / Immo box eeprom programmer!

Windows 7, Vista, Win XP, Win 98 compatible software!

Works on any computer which has got USB port!

Most of V-A-G dashes from 1997 to 2006 are supported!

Direct programming of Megamos ID48 (JMA-TP08) chips to V-A-G cars on CAN bus from November 2003 to June 2006

Transponder Maker Pro is required for pre-programming of these chips.

Note: TP22,23,24,25 transponders are NOT required!



1. Main functions:

 

  Read ecu info

  Read pin code

  Change mileage

  Read eeprom

  Programmer new key

  Write eeprom

  Clear ecu errors

  Viem memory buffer

 

2. List of supported V-A-G cars:

 

Volkswagen



 Golf 5, Caddy, Touran, Jetta, EOS with VDO dash 2003 - June.2006

 Golf 4, Bora with VDO or Motometer/Bosch dash: 1997-2003

 Beetle with Marelli dash: 1998 - 2005

 Passat, Jetta, with VDO, Marelli or Motometer dash: 1997-2004

 Polo with VDO or Motometer dash: 1999-2006 (1999-2002 mileage change only)

 Sharan with VDO dash: 2000-2004(mileage change only)

 Caddy, Lupo with VDO or Motometer dash 1997 - 2002(mileage change only)

 Transporter with VDO dash 1998 - 2000

 LT35 ( Temic immo box) 1999-2003 (pin code read only)

 Gol ( Kostal immo box) 1999-2003 (pin code read only)

 

Seat



 Altea, Leon, Toledo with VDO 2003 - 6/2006

 Leon, Toledo, Cordoba, Ibiza with VDO or Motometer dash 1997-2003

 Alhambrawith VDO 2000 - 2004(mileage change only)

 Inca with VDO or Motometer 1997 -2000(mileage change only)

 

Skoda



 Octavia II with VDO dash 2005 - 6/2006

 Octavia, Fabia with VDO dash 1997 - 2004

 

Audi



 A3 VDO dash 2003 - 2005

 A3,A4,A6 VDO dash 1997 - 2000

 A3,TT,A6 Magnetti Marelli dash 1998 - 2003

 A4 Bosch dash 2000 - 2005

 A4,A6,A8 1995-1999 (immo box - read pin code)

 

3. How to programmer keys with v-a-gtacho usb 4.0



Switch ON ignition with any key new or old, no mater which one.

Start software, select "VDO NEW - CAN bus" from menu.

Press "Connect Selected ECU" button, after 5 seconds the data of the dash will be shown on screen.

Press "Program New Key", software will read data from the dash and after few seconds a new window will be open.

See the picture. ID numbers of the transponders which are stored into memory will be shown.







This is TMPro module#146 window. Insert transponder key with new Megamos ID48 chip and program it.



Press "Add Key" and a message will be shown. Switch ON ignition with key which you want to program! The key may be new - already programmed with TM Pro, or old - key which has been used with the same car! V-a-gtacho will check the key. If this key is already programmed to the car, or it is from another car, V-a-gtacho will show warning message on screen and won't program this key!





If everything is ok, V-a-gtacho will add the new key into the data of immobilizer and will show ID number of new key on screen. See the red mark on the picture. Now you are ready to program the new transponder key into the immobilizer. Press "Write Keys" to complete programming procedure !





Press "Write Keys" and the warning window will be open. If you are sure that everything is all right, press"Continue", otherwise press "Cancel". If you press "Cancel" nothing will happens, and the data won't be written into immobiliser. After pressing "Continue" V-a-gtacho will writes the data into immobiliser after few seconds. The dash will be reset, and the programming procedure will be completed!

This is the last step, after this the new data will be written into immobiliser! If you have marked and erased some keys, they will NOT works anymore!





Press "Write Keys" and the warning window will be open. If you are sure that everything is all right, press"Continue", otherwise press "Cancel". If you press "Cancel" nothing will happens, and the data won't be written into immobiliser. After pressing "Continue" V-a-gtacho will writes the data into immobiliser after few seconds. The dash will be reset, and the programming procedure will be completed!

This is the last step, after this the new data will be written into immobiliser! If you have marked and erased some keys, they will NOT works anymore!

This picture shows the final V-a-gtacho window. If you have switched ON ignition with key which is already programmed by TMPro, the warning lamp of immobiliser on the dash will be turned off. The new key is already stored into immobiliser and you can start engine!

If the immobiliser's warning lamp on the dash is still flashing, there is some error in programming procedure, you can check the transponder key - see how to do this on the next picture!





Switch ON ignition with the key which you want to test! Start software, select "VDO NEW - CAN bus" from menu, and press"Transponder Check". V-a-gtacho will connects immobiliser. Press "Read ECU Info" button, and wait about 10 seconds. The information about this transponder key will be displayed on screen, see the next picture. You can press "Read ECU Info" to testing of transponder key again. This procedure is optional, and is not required when programming the new keys.





Switch ON ignition with the key which you want to test! Start software, select "VDO NEW - CAN bus" from menu, and press"Transponder Check". V-a-gtacho will connects immobiliser. Press "Read ECU Info" button, and wait about 10 seconds. The information about this transponder key will be displayed on screen, see the next picture. You can press "Read ECU Info" to testing of transponder key again. This procedure is optional, and is not required when programming the new keys

Transponder variable part and transponder locked must be "YES", otherwise there are errors in programming of the new key with TMPro!

Transponder fixed part must be "YES" otherwise the key is still not programmed into immobiliser, or V-a-gtacho programming procedure is not completed successfully. In case of such error, repeat whole programming procedure again with another new transponder! All parameters must be set "YES"!





 


Escanear código QR Cocheobd2 a pedir en cualquier lugar y en cualquier momento por el móvil.

Cualquier problema o más información, puede contactar con nosotros a través de:

Email:sales@CocheOBD2.es
Whatsapp: +86 18064450969/+86 15260206197
Skype:cocheobd2.com

Por favor, deje su número de teléfono para el envío expreso.

¿Cómo comprar en cocheobd2.es?